S E C O N D - H A N D     P O W E R - P L A N T S
2 nd  Site
We will need a signed and sealed LOI with bank-information by fax before we send hardcopies, pictures, tapes etc.
BOOKMARK THIS PAGE AND COME BACK OFTEN OFFERS CHANGE FREQUENTLY

Second - Hand POWER-PLANTS        LIQUIDATIONS

MODEL 6B5.9 CUMMINS ENGINES
CATERPILLAR  XQ1750 KW
CAT D348TA package
37.4 MW(50Hz) Gas Turbine-Generator Sets
POWER PLANT FACILITY
POWER PLANT FACILITY 2
115 MW (50Hz.) Diesel Engine Gen Station
100   MEGAWATT BARGE
CUMMINS VTA 28\GS
800kW STEAM TURBINE GENERATOR
2 x 10MW GAS TURBINES
20 MW POWERPLANT
5 x  CAT. 3512 Power Module Gensets
CAT. 3516
CAT 3516TA
NEW, CATERPILLAR 3512TA Turbo Charged
6 MW POWER PLANT
12 MW EMD POWER PLANT
DETROIT DIESEL 14912V
COMPLETE 26MW POWER PLANT
SOLAR CENTAUR'S 
360MW, NATURAL GAS/CRUDE OIL fired thermal Power Plant

MODEL 6B5.9 CUMMINS ENGINES
190 HP Mechanical Fuel Injection
51 units available………………………… $ 6950.00USD each

190 HP Electronic Fuel Injection
5 units available …………………………..$7450.00USD each

175 HP Mechanical Fuel Injection
6 units available………………………….. $6950.00USD each

195 HP Electronic Fuel Injection
2 units available …………………………..$7450.00USD each

These engines are complete and were designed for truck application; however, they can be used for generator sets.  All units are NEW, 1998 or newer and have never been installed.
Prices shown are for “take-all” sale.  Offers will be considered for different quantities then shown above.

Accessories include:  water pumps, fan hubs, pulleys & belts, fuel systems.
Not included:  flywheels, starters, alternators, fans.

Mechanical fuel injection engines can easily be adapted to generator application.  Electronic fuel control engines require electronics which need to be purchased separately from a Cummins dealer/supplier.   FULL FACTORY WARRANTY WITH THESE UNITS.  PLEASE FAX OR E-MAIL ALL OFFERS.

CUMMINS TRUCK ENGINES
NEW, UNUSED WITH WARRANTY
1998   M11-400   (400HP)

60 UNITS AVAILABLE
CUMMINS “over the road” truck engines, NEW, never installed, available due to cancelled order.  FULL FACTORY WARRANTY.

Complete units except for starters, alternators, flywheels.  Price includes fuel systems, belts, pulleys, water pumps, fan hubs, flywheel housings.

Price is below fleet owners price direct from factory.  Price is based upon
“take all” units.  Smaller quantities will be considered upon request.

ENGINE MODEL NUMBER M11-400
RATED 400HP, can be turned down to 80HP without internal adjustment.
Price each unit……….$ 14,900.00USD FOB USA



Sound Attenuated Utility Grade                                                                       top
Caterpillar XQ1750 3516 DITA Diesel Power Module
  Caterpillar  XQ1750 KW  (1400kva@50Hz)
  Features :
     40' Container
     Chassis
     1250 Gal Fuel Tank
     CAT EMCP Floor Standing Control Panel
     Utility Grade Auto Paralleling Switchgear
     Auto Start/Stop
     Safety shutdowns
     Circuit breaker
     Batteries
     Battery charger
     Muffler
     DC Interior Lighting
     Sound Attenuated
 2 units available
 Year 1998
Hours  Unit 1 = 450 and      Unit 2 = 550
Price each unit $ 622,000.00USD plus shipping
CAT 5YR/10000 Hour Extended Service Coverage
Immediate availability



CAT D348TA package          top
 899 hours since new
 600kW
 $44,500.00 USD
 Loadtested, serviced, painted

37.4 MW(50Hz) CE Frame 68          top
Gas Turbine-Generator Sets

Refurbished, Frame 6B gas turbine-generator sets, simple cycle power islands as described herein:

 (3) refurbished GK Frame 68 gas turbine generator equipped to fire on both distillate fuel oil (#2 Diesel) and natural gas and including all normally associated unit components. These units were built in 1982:
?
* Accessory / Turbine base with gas turbine and associated systems.
* Generator base with generator and reduction gear.
* Cooling water piping and temperature regulating valve. The systems are designed to serve two units and be 100% redundant. The third unit will have a single cooling unit sized at 100% but not redundant.
* Cooling water heat exchanger is base and main plate type heat exchanger arrangement.
* Cooling water pump and auxiliaries.
* Exhaust frame blower arrangement.
* Fuel oil forwarding skid, associated piping, and all related fuel oil system components between the skids and the units,
* Liquid fuel pumps, flow dividers, filters, strainers, piping, etc.
* Fuel gas supply system including associated piping, valves, strainers, etc.
* Atomizing air compressor, booster compressor, cooler, temperature control  valves, and associated piping.
* Control equipment including: SpeedTronic Mark lV, generator control panels, excitation control panels, interconnecting cables where removable, generator breakers and cubicles, 10,500 volt switch gear including PT’s and CT’s, 5000 volt cranking motor starters, and all other motor control centers (A.C. and D.C.),
* Batteries, battery rack, and charger. ” Fire Protection system.
Inlet air system’. Ducting, silencers, filter house, structural steel.
Lube oil vent mist eliminator system.
* Generator cooling system: complete with piping, coolers, valves, structural steel, etc.
* Turbine exhaust plenum arrangement up to expansion joint.

REFURBISHED   FRAME 68 GAS TURBINE GENERATOR SETS
Gas Turbines
ISO Rating 37,400 kW
Configuration Single Shaft / Two Bearing
Turbine Operating Speed (RPM) 5,135
Compressor (axial flow)
Stages 17
Variable Inlet Guide Vanes (1GV’s) Standard, High Flow - Optional

Materials:
Rotor Blades - Refurbished 403 w/ NiCd Plating
Stator Blades - Refurbished 403 w/ NiCd Plating
IGV’s 403 w/ NiCd Plating, GTD 450- Optional

Turbine (heavy duty)
Stages 3
Max Temperature (degrees F) 2020 F (Base Load)

Materials:
Rotor Buckets
1st Stage GT9-1119S - New (current production)
2nd Stage (PARA)
3rd Stage IN-738- Refurbished or New (PARA)U-500-
Refurbished
Nozzle (1st Stage) FSX-414- Refurbished
Nozzle (2nd Stage)(PARA)
Nozzle (3rd Stage) FSX-414- Refurbished
(PARA)FSX-414 - Refurbished
Rotor wheels Cr Mo V - refurbished
Bearings
Radial Type(2) Eliptical
Thrust Type(1) Tilt-Pad
Combustion
Type Cannular - Reverse Flow
Numbers of Chambers 10

Materials:
Liners: Hastelloy X
Transition Pieces Hastelloy X
Ignitors, Qty. 2
Flame Detectors, Qty/Type 4 / Ultra-Violet
Load Gear
Reduction Gear
Manufacturer Graffenstaden - Refurbished
Configuration Vertical Offset
Speed Ratio (RPM) 5,135/3,000

Generators
Synchronous Generator
Type TEWAC - Refurbished
KVA Output @ .9 Pf / 80 Fair inlet 45,000
Rated terminal output power 10.5 kv, 2750 A
Cooling System TEWAC
Control System
Control Panels
Manufacturer GE Drive Systems, Salem, VA
Model Mark IV TMR
Type Microprocessor based control systems
Display CRT monitor
Operator input Membrane switch panel
Control Panel Supply 125 VAC
Auxiliary Power Supply l15 VAC
Enclosure NEMA Class 1
Excitation System
Control Panels
Manufacturer Alsthom
Type Microprocessor based control systems
Operator input Knobs, Buttons, Switches, & MARK IV
Exciter Hardware Brushless (Holec)
Field Voltage Class 250 VDC
Control Panel Supply 125 VDC
Auxiliary Power Supply 115 VAC
Auxiliary Systems
Fuel
Fuel Oil (#2) Distillate Fuel Oil (GE1-41047H)
Fuel forwarding A.C, pumps for forwarding
Lubrication Oil
Configuration Common-Turbine / Generator
Oil Type Mineral Oil (GKK-32568)
Mail Oil Pump Positive Displacement
Driver Accessory Gear Driven
Auxiliary Oil Pump Centrifugal
Driver A.C. Motor
Emergency 0il Pump Centrifugal
Driver D.C. Motor
Lube Coolers Water Cooled - Siagle, Shell & Tube heat exchanger
Starting System
Configuration Motor (5kV) - Refurbished
Manufacturer Schorch
Inlet Air/Exhaust
Air Filter Mfg. Doanldson, Farr or Equal
Type Static two stage
Inlet Press Loss, in H2O 4.0
Exhaust Press. Loss, in H2O 2.5
Fire Protection Type High Pressure CO2
Detectors Temperature Sensors

REFURBISHED GAS TURBINE GENERATOR
ACCESSORY EQUIPMENT
The turbine is a heavy duty base mounted self contained system. The system includes accessory equipment such as lubrication oil pumps, gauge & instrument panel, oil filtration, starting  motor, torque converter, oil cooler, fuel flow divider, fuel pumps, fuel valves, accessory gear, atomizing air compressors, hydraulic ratchet system and other base mounted subsystems.
Compressor
The compressor consists of a radial inlet casing providing uniform circumferential inlet flow to the compressor, inlet guide vanes to direct the inlet air angle, and large chord, sub- sonic compressor blading (stainless steel) providing a rugged air path design with wide operating limits. The 17 stage compressor is a proven high efficiency design with demonstrated long life in vigorous applications and environments.

Stator Casings
Casings are horizontally split to facilitate ease of inspection and maintenance. Turbine shell and exhaust frame cooling provides dimensional stability to maintain close rotor clearances necessary for optimum tong term high efficiency and performance.

Combustion
Atomizing dual fuel nozzles provide even fuel flow. Reverse flow combustion chambers (increased combustion path strength) minimizes temperature variations and prolongs life of parts. Ultraviolet flame detectors are mounted on combustion casings to sense the presence of combustion. Gas fuel is distributed uniformly via a fuel gas manifold. Similarly, an atomizing air manifold provides uniform air distribution to assure uniform and complete combustion of liquid fuel. An atomizing air pre cooler reduces the temperature of the pressurized air.

Turbine
The nozzle cooling design increases the nozzle life and reduces the bulk metal temperature. The three stage, high efficiency impulse design turbine utilizes high energy air foils (buckets) with large temperature drops taken across stationary nozzles to produce conservative temperatures in rotating components. Turbine wheels are maintained at design temperature by control of wheel space cooling air temperature and built in mechanical design features, including bucket shank seals and cooling circuit design. The turbine compartment vent fan provides outside air to the turbine compartment during engine operation.

Exhaust
The unit exhaust temperature is controlled osing type K thermocouple measurements  which provide rapid response and high accuracy to the Mark IV SpeedTronic control system. The exhaust discharge can be directed upward or to either side.

Turbine Controls
The Mark 1V SpeedTronic control system provides all turbine generator control functions with thc exception of generator excitation and protection. The Mark IV SpeedTronic control system is a State-of-the-art modular system designed specifically to control GE gas turbines. This control system provides comprehensive supervisory control of all turbine operating parameters as well as an optional interface to customer controls and monitoring equipment. The Mark IV SpeedTronic control system can operate remotely via the customers DCS system.

Generator
The generator is a totally enclosed water to air cooled (TEWAC), synchronous machine. The generator package houses the generator, the generator cooling system, and the load   gear is a weatherproof enclosure mounted on a steel base. The generator is designed specifically for use in a packaged power plant. Air is circulated by the generator fans through the stator body and coolers to assure even cooling of the generator.

Speed Reducing Load Gear
The gear is a vertically offset double helical type which results in a straight line up of the gas turbine and generator. The load gear is direct coupled to the generator field shaft. A flexible coupling connects the gas turbine to the load gear.

Excitation
The brushless excitation system provides the field current at the rotor. The automatic voltage regulator function holds the generator terminal voltage within narrow limits as the generator demand changes. The high initial response of’ the static excitation system minimizes voltage fluctuations during system disturbances. The regulating system uses the voltage and current feedback signals to create the appropriate stationary field current to influence the brushless exciter to produce the correct rotating field current. This system has no carbon brushes, and therefore requires on1y periodic cleaning and calibration.

Technical Information Letters (TILs)
GE regularly issues TILs to advise customers of improvements, problems, and other issues that can affect the normal safe operation of the gas turbine generator and accessory equipment supplied by GE. Unfortunately, some customers fail to implement these recommendations in a prompt manner. Therefore, all TIL’s relevant to the particular gas turbine generator and their associated sub systems are reviewed and applied to the units if not already applied. A listing of all relevant TIL’s is included with the refurbishment documentation as is a statement that these have all been applied to the unit.

ESTIMATED SYSTEM PERFORMANCE CHECK
Basic Load Operation
Units Uprated to 2055 Firing Temperature
Gas Fuel: 59F 90F
Output (kW) 37,860 33,800
Heat Rate (BTU/kW-Hr) 11430 11,770
(PARA)
Distillate 59F 90f
Output (kW) 36,990 30,030
Heat Rate (BTU/kW-Hr) 1l,540  11,880
Unit witb 2020 Firing Temperature
Gas Fuel: 59F 90F
Output (kW) 34,910 30,720
Beat Rate (BTU/kW-Hr) 11,730 12,110
(PARA)
Distillate 59F 90F
Output (kW) 34,160 20,050
Heat Rate (BTU/kW-Hr) 11,840 12,230
Site Condition Assumed to be:
Elevation-ft. 0
Site Pressure – psia 14.7
Inlet Drop - in water 4.0
Exhaust Loss - in water 2.5
Relative Humidity - % 60
Application - Base Load
Combustion System - Dual Fuel (#2 and Gas) dry
Rated Firing Temp - Degrees F 2020 (1 unit) / 2055 (2 units)
EQUIPMENT WARRANTY
The equipment described here in carries a full ”New Unit ” warranty for one year after startup (commercial operation date) or eighteen months after shipment whichever occurs first. The turbine generator accessories, etc. are all covered by this warranty.
WARRANTY VALIDATION
The warranty is validated by the lead GE Technical Advisor (TA) who witnesses and advised on the proper installation and startup of the gas turbine generator and associated sub systems.



750 KW  Caterpillar Model D349TA        top
 
Standby takeout Diesel Generator Set

750kW Caterpillar Model D349TA

Premium control panel, 
auto start/stop, safety shutdowns,
electronic governor,
circuit breaker, 
muffler, radiator

one (1) unit available, only 69 hours.......$75,000.00
Only $100.00 per kW!!!
Loadtested, serviced, painted
Subject to prior sale.


POWER PLANT FACILITY           top
This generation facility consists of the following major components:
1)  Two (2) Cooper Bessemer Model LSV 16SG Gas Engines rated 4550 HP
     at 327RPM, series #’s 6979 and 6980.
2) Two (2) Westinghouse Model ES single bearing generators, 2300/4160V,
      60HZ, 3500 KW each, series #’s 1S72P865 and 2S72P865.
3) Two (2) Horizontal remote radiators with 480V, 25HP TEPC motor driven
fans for jacket water cooling, two Ross shell and tube heat exchangers for oil cooling.
4) Two American air filter self-cleaning oil bath air cleaners.
5) Two (2) 24” Maxim M21 vertical exhaust silencers.
6) One (1) Gas/gasoline engine driven 250 PSI starting air compressor with 1000 gallon, 250 PSI receiver.
7) Complete switchgear set-up including 2-motor operated draw out circuit breakers, synchronizing swing panel with sync lites and synchroscope, dual ammeter, voltmeter, frequency meters and under/over frequency protection.
8) One 50x50 steel building with 25’ eave height, one 14x22 steel building used for housing generator sets and switchgear.
9) A large quantity of spare parts for the systems enclosed withing fenced area.
All piping, valves and vessels related to the systems, located at the facility.
The two above units are block mounted, the engines are being pre-lubed and rotated monthly, and the generators are heated 24 hours daily.  The units were manufactured in the late 60’s and were installed at the present location in 1979.
The engines required only minor repair in 1979, but the generators were fully rebuilt.  The units ran until 1982 when a major power line was installed.  The engines have the new style, “cageless” power cylinder heads.  All plant piping is above ground and entire plant is  “match-marked” with engineering drawings, for total plant re-installation.

POWER PLANT FACILITY
1.  Engine-Cooper LSV – 16 - SC, super charged gas engine purchased in 1967.
     Hour Meter reading before overhaul 73,090 – date  1-8-76
     Estimated Hours operated since overhaul  27,722
(1) Replace all piston rings
(2) All valves and heads reworked
(3) Replaced piston liners # 2, 3, 5, & 6 on left-hand bank
#1 , 3, 5, & 7 on right hand bank
(4) Replaced all crankshaft main and rod bearings
Generator – Type & Frame – Westinghouse ES 11S
KVA – 4375
AMP – 608
VOLTS –4160
%  P.F. – 80
Phase
Hz –60
RPM – 327
EXC. AMP – 76.9
EXC VOLT –250
TEMP. RISE – 60 C
TEMP. MEAS. METHOD – DETECTOR
INST. BOOK – 4500 – 50
Serial No. – 25 -72P - 865
II. Engine – Cooper L6V-16-SG  Supercharged Gas Engine –
Purchased in 1967.  Hour Meter reading before overhaul
85,578 – date 12-9-77
Estimated Hours operated since overhaul 13,250
(1) Replaced crankshaft and line bored block
(2) Replaced all crankshaft main and rod bearings
(3) Replaced  piston rings
(4) All valves and heads reworked

Generator Type & Frame – Westinghouse ES 11S
KVA – 4375
AMP – 608
VOLTS – 4160
% P. F. – 80
Hz – 60
RPM – 327
EXC, AMP – 76.9
EXC. VOLT –250
TEMP. RISE –60 C
TEMP. MEAS. METHOD – DETECTOR
INST. BOOK – 4500 – 50

Complete paralleling switcher is included.
Above ground and reusable
Plant  “As Built” drawings are available to purchaser.
Systems are match marked for removal / reassemble.
Many original manuals and prints are available.
Notes on Preservation
Units were last operated in 1982.  At shutdown the generators were covered and heat was applied to eliminate condensation and preserve insulation integrity.
A program of regular has preserved the engines operation of the prelude system and rolling the engines to oil all internals and to keep the bearings and shafts from degrading.


POWER PLANT FACILITY2  PRICE   $  700,000.00  top
This generation facility consists of the following major components:
1)  Two (2) Cooper Bessemer Model LSV 16SG Gas Engines rated 4550 HP
     at 327RPM, series #’s 6979 and 6980.
2) Two (2) Westinghouse Model ES single bearing generators, 2300/4160V,
      60HZ, 3500 KW each, series #’s 1S72P865 and 2S72P865.
3) Two (2) Horizontal remote radiators with 480V, 25HP TEPC motor driven fans for jacket water cooling, two Ross shell and tube heat exchangers for oil cooling.
4) Two American air filter self-cleaning oil bath air cleaners.
5) Two (2) 24” Maxim M21 vertical exhaust silencers.
6) One (1) Gas/gasoline engine driven 250 PSI starting air compressor with 1000 gallon, 250 PSI receiver.
7) Complete switchgear set-up including 2-motor operated draw out circuit breakers, synchronizing swing panel with sync lites and synchroscope, dual ammeter, voltmeter, frequency meters and under/over frequency protection.
8) One 50x50 steel building with 25’ eave height, one 14x22 steel building used for housing generator sets and switchgear.
9) A large quantity of spare parts for the systems enclosed within fenced area.
All piping, valves and vessels related to the systems, located at the facility.
The two above units are block mounted, the engines are being pre-lubed and rotated monthly, and the generators are heated 24 hours daily.  The units were manufactured in the late 60’s and were installed at the present location in 1979.
The engines required only minor repair in 1979, but the generators were fully rebuilt.  The units ran until 1982 when a major power line was installed.  The engines have the new style, “cageless” power cylinder heads.  All plant piping is above ground and entire plant is  “match-marked” with engineering drawings, for total plant re-installation.

POWER PLANT FACILITY
1.  Engine-Cooper LSV – 16 - SC, super charged gas engine purchased in 1967.
     Hour Meter reading before overhaul 73,090 – date  1-8-76
     Estimated Hours operated since overhaul  27,722
(1) Replace all piston rings
(2) All valves and heads reworked
(3) Replaced piston liners # 2, 3, 5, & 6 on left-hand bank
#1 , 3, 5, & 7 on right hand bank
(4) Replaced all crankshaft main and rod bearings
Generator – Type & Frame – Westinghouse ES 11S
KVA – 4375
AMP – 608
VOLTS –4160
%  P.F. – 80
Phase
Hz –60
RPM – 327
EXC. AMP – 76.9
EXC VOLT –250
TEMP. RISE – 60 C
TEMP. MEAS. METHOD – DETECTOR
INST. BOOK – 4500 – 50
Serial No. – 25 -72P - 865
II. Engine – Cooper L6V-16-SG  Supercharged Gas Engine –
Purchased in 1967.  Hour Meter reading before overhaul
85,578 – date 12-9-77
Estimated Hours operated since overhaul 13,250
(1) Replaced crankshaft and line bored block
(2) Replaced all crankshaft main and rod bearings
(3) Replaced  piston rings
(4) All valves and heads reworked
Generator Type & Frame – Westinghouse ES 11S
KVA – 4375
AMP – 608
VOLTS – 4160
% P. F. – 80
Hz – 60
RPM – 327
EXC, AMP – 76.9
EXC. VOLT –250
TEMP. RISE –60 C
TEMP. MEAS. METHOD – DETECTOR
INST. BOOK – 4500 – 50

Complete paralleling switchgear is included.
Above ground and reusable.
Plant  “As Built” drawings are available to purchaser.
Systems are match marked for removal / reassemble.
Many original manuals and prints are available.
Notes on Preservation
Units were last operated in 1982.  At shutdown the generators were covered and heat was applied to eliminate condensation and preserve insulation integrity.
A program of regular maintanence has preserved the engines operation, the prelube system and rolling the engines to oil all internals to keep the bearings and shafts from degrading.



115 MW (50Hz.) Diesel Engine Generating Station     top
Equipment for Sale (All or Parts)

This diesel generating station was completed and put into operation at the end of 1995. The station has 9 diesel engines type 9TM620 manufactured by STORK-WARTSILA DIESEL CO., HOLLAND
 with a single unit capacity of 12.75 MW;
9 matching generators type HSG1600S14 were
manufactured by ABB, FINLAND with
a single unit capacity of 12.43 MW.
The 9 sets were installed into 3 relatively independent units.

The 110 kV switchyard is equipped with 3 main-transformers 121 kV/11kV 47 MVA type STROD/BTROD
CL-2 manufactured by TAKAOKA ELECTRIC CO. LTD., JAPAN. The 110kV GIS was manufactured by
NISSIN ELECTRIC CO. LTD., JAPAN.

The automation level is high since the on-line computer monitoring system is also controlling the substation. The
power generation units have been extremely reliable since placed into operation. The annual consumption of fuel
oil (180 cst heavy fuel oil) is 183 g/kwh.
 The annual consumptin of lube oil is 1.6 g/kwh.
 The total operation hours are 2000--2500 hrs.

Since the power generation sets are
excessive to present needs, all equipment is for sale.
 Offers for individual equipment will be considered.

More information available on request.


100   MEGAWATT BARGE MOUNTED POWER PLANT      top

We can provide a 100   MW Barge Mounted Power Plant, complete, ABS Certified, consisting of two (2) 50 MW Gas Turbine Generators.
Outputs are at ISO conditions.  These units will be refurbished and ready to operate on either Natural Gas or Fuel Oil and installed on an ABS certified barge.  Delivery can occur within approximately 120 working days (4 months) after receipt of funds as specified below.
The two Gas Turbines will be set up to operate singularly or in parallel.
The Generator output will be 10,800 volts, 3-phase, 50 HZ.  The power will be transported to shore by overhead transmission lines at Generator voltage.  A control room will be provided together with switchgear and circuit disconnects.

The customer/buyer will be responsible for providing all fuel needs including delivery and storage of fuel.  The customer will also be responsible for all Grid connections and transformation of power.

We will provide, as part of the Barge package, an emergency generator for lighting and Barge pumps.  The Turbines can be started with electric motors powered from the emergency generator (diesel fueled) or by pressurized air.

All of this equipment is offered subject to prior sale.  The costs will be adjusted accordingly if additional or substitute equipment is required by customer.

The two (2) Gas Turbines can be adapted to operate on Heavy Fuel (HFO) or Bunker “C” or #6 Fuel oil, providing proper oil treatment modules are utilized.  We will offer this equipment under separate Contract.

ESTIMATE OF COSTS:
100 MW Power Barge can be furnished as described for approx. $300.00 USD/ kW or $ 30,000,000.00.
Any commissions, “finders fees”, or other unidentified costs, shall be added to the cost shown here.  At this price, USED equipment is utilized.

To prepare a formal quotation and provide detailed equipment specifics, i.e. model numbers, serial numbers, etc., a one-percent (1%) Cash Advance shall be placed in an escrow account with draws for the preparation of same and expenses incurred.  An Executed “Non-Disclosure, Non-Compete, Non-Circumvent Agreement” must be signed by the “end-user”.  It will take two (2) weeks, after receipt of one-percent (1%) cash advance funds, and after ALL pertinent information regarding the ultimate construction of the barge is received by us from the buyer, to prepare the Formal Quotation.

After receipt of the Formal Quotation/Proposal,  buyer shall have two (2) weeks to place a five-percent (5%) refundable deposit which will allow him thirty (30) days to perform “due diligence”.  At the end of this “due diligence” period, buyer shall pay eighty-five percent (85%) of the total purchase price.  The balance due shall be paid upon customer acceptance of the unit.

Currently, we have a “window” of opportunity open to immediately initiate necessary engineering work.  This work will be accomplished by “World Class” Maritime Contractors; therefore, meeting the highest of Standards.

NEW 1999 MODEL POWER BARGE
We can furnish 100MW Power Barge complete with two (2) new, state- of- the-art 1999 model, Westinghouse Turbine Gensets, 50 Hz, for approximately $ 420.00/kW.  Same terms as abov


CUMMINS VTA 28\GS              top
DIESEL - 1993 MODEL
515 KW STANDBY UNIT
RADIATOR COOLED
AIR CLEANER
MUFFLER
ELECTRONIC GOVERNOR
24V STARTER
SKID MOUNTED
ENGINE PANEL
SAFETIES
NEWAGE GENERATOR END
277/480 VOLT
3 PHASE
60 HZ
CIRCUIT BREAKER 800A
20' ISO CONTAINER
7,500 HOURS SINCE NEW
LOADTESTED, SERVICED, PAINTED
 $ 42,000.00 or best offer
F.O.B. WESTERN USA

800kW STEAM TURBINE GENERATOR      top
800kW STEAM TURBINE GENERATOR
REFURBISHED TURBO GENERATOR
TURBINE                               Mitsui Brown Boveri MTG 211
GENERATOR                  Fuji Electric
TURBINE SPECIFICATIONS:
Rated output (electric load)                   800kW
Normal output (electric load)                 640kW
Turbine rated speed                               10036 RPM
Generator rated speed                              1800 RPM
MAIN STEAM CONDITION:
Rated pressure                                           8.0kg/cm2
Rated temperature                                  Saturated
Normal pressure                                       6.0kg/cm2
Normal temperature                                  260 deg. C
800kW                                                  13atg x 350 deg.C x 6480Kg/hr
600kW                                                    6atg x 250 deg.C x 4860Kg/hr
Condenser vacuum                               680mmHg – 720mmHg
SPECIFICATIONS OF GENERATOR:
 Type                                                     GFV 2504M 44W3D
Specifications                                        800kW / AC./450V/60HZ
CLASSIFICATION CERTIFICATE:
The unit was inspected and approved by The Classification of
Lloyd’s Register.  The Classification Certificate is available upon inspection.

FURTHER DETAILS AND PRICE UPON REQUEST
PLEASE FAX OR E-MAIL OFFERS IF INTEREST EXISTS


2 x 10MW GAS TURBINES      top
For IMMEDIATE SALE :
2 x 10MW GAS TURBINES
Dual fuel (natural gas / diesel)
Varying speed gear boxes, currently at 60Hz,
convertible to 50Hz.
Stand-by units, 4000 hrs. / -
3 easy-bolt together Modular units
Orenda turbines, 18 stage
G.E. generators,1800 rpm, 2300/4160V.
These units are in MINT CONDITION.
Price is $1.8mil USD
Full specs upon financial qualification and LOI.
10% deposit required prior to inspection, totally
refundable upon acceptance or decline.



2 MW English Electric Natural gas turbine      top
2 MW English Electric Natural gas turbine
Type EM27P
Low hours, stand-by unit
2 shaft recouperative
nat gas 2680D 14.7 psi  59 deg. F
Late 60's vintage
Turbine at 7050 RPM
Generator  2MW,  4160V
Price.....$150,000.00 USD
10% Inspection deposit
Complete specs upon financial qualification



20 MW Power Plant           top
5 each available EMERGENCY DIESEL GENERATORS
Cooper Bessemer 5600HP Model KSV-16T
16 cylinders
Ideal Electric Generator, 5000kva, .8 power factor
4160 volts, 60cycle, 600 RPM, Skid mounted
Brushless Exciter
Year of Mfg. 1970
Unit #1   4060 hours
Unit #2   3759 hours
Unit #3   3424 hours
Unit #4   4239 hours
Unit #5   3733 hours
Compair-Luchard air start system
Jacket water heater skid and control cabinet
Westinghouse WDPF monitoring system (data acquisition)
$2,500,000.00 spare parts available with generator purchase
Also available, spare NEW generator


CAT. 3516                                   top
  4 UNITS   BRAND NEW IN CRATES
14 UNITS, LATE MODEL, LOW HOURS….
MOST UNITS UNDER 2000 TOTAL HOURS
2000KVA standby  1825KVA prime @ 50Hz
1460kW (1825KVA), 415 volt, 3 phase, 50Hz, 1500 RPM
Easily converted to 60Hz, 1800 RPM, with simple speed change.
COMPLETE:
Single stage air cleaners
Radiator and engine driven fan
CAT EMCP control panel
CAT 24 volt battery
CAT SR4B Generators
9 units of step up transformers 415V / 11000V, 3500 mva each
Capable for 2 gensets each
Exhaust silencers and remote framework
18 generator control, synch and circuit breaker panels
High voltage switchroom for the 18 generators
Discount for all 18 units


CAT. 3516TA                                   top
3 units  x  1750kW each
Currently at 50Hz, can be converted to 60Hz
with simple speed change
$150,000.00 each unit
Add $5000.00 per unit for U.S. FOB
Low hours.
Details upon request.

Caterpillar 3516TA,
2000kW, 1992 model, 456 hours, 480V,
60Hz, Kato generator, remote radiator,
new circuit breakers, meter panels, auto start/stop,
silencer, block heater, skid mounted. Excellent condition.
Only $125.00 per kW!
$250,000.00USD
Immediate availabiltity, subject to prior sale.



5 x  CAT. 3512 Power Module Gensets        top
all under 6,000 hours, rated 1150 kva / 50 hz or 1250 kva / 60 hz 3300v / 4160v, 3ph, 4 wire,  1500/1800 rpm
Kato generators Skid mounted units NO radiators / Fully enclosed, LIKE NEW
$ 160,000.00 each unit   /    Discounted if all 5 units are sold.


NEW, CATERPILLAR 3512TA Turbo Charged         top

NEW, CATERPILLAR 3512TA Turbo Charged
Diesel Oilfield Land Power Modules
4 cycle, V12, 6.7 Bore, 7.5 Stroke
Weight:  38,600 lbs. each
18 units available.....$245,000.00 each
IMMEDIATE PICK-UP / DELIVERY
(minimum 4 units)
5 year Electrical and Mechanical Warranty
FOB NORTH AMERICA


6 MW POWER PLANT        top
2 x GEC Ruston Generator Sets
These 2 units are almost brand NEW,  1996 models.  Warranty expired 7/99.
ORIGINAL cost over $4,000,000.00USD when installed.
OFFERED NOW FOR  $1,750,000.00USD.

These units are currently running at 750 rpm and can be sped up to 900 rpm
to achieve 60 Hz.  These are the latest models on the market.  These would be great units for oilfield or mining applications.
2 x GEC Alstom Ruston
2838 kW each
 Diesel Power Generators
comprising of:
2 x Ruston 12 vee type Cylinder Diesel Engines.
Model 12RK270, Mark 2

 WITH  Napier type exhaust gas driven turbochargers.
 2 x Leroy Sommer 2849kW…. 3565 kva alternators,
 Type LSA56VL85/8P, 6600 volts, AC brushless type.
 GEC Alstom Engine Control and Instrumentation panels.
 Compressed air starting motors with 3 Compair air compressors
 Model 5213, 30.6 cfm each.
 Radiator cooling system, charge air intake system, engine exhaust
 system, lubrication oil storage, waste oil storage, Alfa Laval fuel/oil
 blending system.
 Rowater reverse osmosis plant.
 2 x Weatherproof enclosures.

 HOURS
 Unit 1 = 3906 hours, 19,745 total hours, fully REBUILT at 15, 839,
                under warranty by GEC.
 Unit 2 = 22,052 total hours, no rebuild yet.
 Both units were under GEC Warranty until July 1999.


12 MW EMD POWER PLANT        top
Consisting of 6 x 2000kW EMD units,
4160/6600V Transformer included if required.
Units operate at 50Hz or 60Hz. Woodward Governor.
Low hour units, turbocharged engines,
skidded and enclosed, 154 GPH fuel rate,
900 RPM, air cooled.  Control room with
synchronous switchgear, 2500kva, 3 ph.
radiators, mufflers, fuel tanks on each unit.
Price USD $2mil (includes transformer if required)
Perfect, LIKE NEW CONDITION.
10% deposit / LOI holds units pending inspection.


Detroit Diesel 14912V        top
Model 600SRSE
500kW Kato generator
4160V, 60 Hz
1800 RPM
573 total hours
Electric start, main breaker, meter panel,
skid mounted
Loadtested..............$45,000.00USD
Immediate delivery


COMPLETE 26MW POWER PLANT        top
26MW  HFO POWER PLANT
or  12.4MW or 13.6MW HFO POWER PLANT
Consisting of:
2 x 6800kW Siemens Engine Generators
GMT 9800HP, 514 RPM
Heavy #6 fuel oil with
Single bearing 4160V, 60Hz, .08pf
generators, complete with switchgear, control panels, cooling systems and spare parts
& 2 x 6200kW Siemens Engine Generators
MAN 8L52/55A, 8430HP, 450 RPM
Heavy #6 fuel oil with
single bearing 4160V, 60Hz, .08pf
Convertible to 50Hz

COMPLETE 26MW POWER PLANT
$ 3,900,000.00USD
“as is, where is”
 ( $ 150.00 per kW )
or will sell in pairs.
Letter of Intent accompanied by
5% holds units pending inspection.
Engineering, relocation and Turn-key installation including cost of units……$300.00 per kW.


Solar Centaur's        top
3 units available (12MW)
Almost unused Centaur 50 Gas Turbines,
4 Mw each, 50 Hz, 6.6 kV, can convert to 60Hz.
Gas-fired, 'as new' from a cancelled project. One unit never installed.
The other two units have only run for 2 and 6 weeks before being shut down.
They are fitted with diverter valves and bypass stacks so are ideal for
cogen applications.  Fuel gas booster compressors available with the
purchase of all 3 units at additional cost.
US$ 3.9 Million ($ 325.00 per kW)
Turnkey installation available at $ 500.00 per kW or less including cost of units.


360MW, Natural gas/crude oil fired thermal power plant        top
Cost installed, up and running, operational $180 Mil USD ($500.00 per kW).
The plant will consist of two trains, complete with buildings,
boilers, turbines, generators, switchgear, substation, .. complete plant!
We will supply the plant, install it, put it in operation and train the personnel to run it.
A thermal plant...uses about 30% less fuel per Kw than a combustion turbine does,
has a longer service life, less emissions, and we can have it up and running for less
cost than an equivalent combustion turbine plant.  Also we can add some additional
processes to it if required.
 
 

Road Town - Tortola
British Virgin  Islands
 
Fax: 1 206 337-0754

pwrgenerators@ch-non-food.com

 

Main-PageCommoditiesSecond Hand PlantsPowerplantsNapkin LineR R PBlastrakHeavy EquipmentField HospitalYachts